AVComm

From ECWiki

(Difference between revisions)
Jump to: navigation, search
(Portable/Party Equipment)
(Recommended Speaker Configurations)
Line 18: Line 18:
* HDTV Tuner for Projector
* HDTV Tuner for Projector
-
==Recommended Speaker Configurations==
+
==Recommended Speaker Configuration==
-
* Standard party speakers: MX1400 house out --> USA900 in <i>STEREO</i> --> JBL MR835s on left/right channels
+
*Parties: use the 2 JBL PRX612 powered speakers. Plug them into the wall. Make sure the speakers are '''OFF'''. Plug something with 1/4" TS cables into each speaker. Plug the other end of the cable into a line-level audio input. Make sure the speakers are set to '''Line Level Sensitivity, not mic level''' turn the speakers '''on.''' Typically, the cable used will be 1/8" TRS -> dual 1/4" TS.
-
* Mono Amp/Quad Speakers: MX1400 house out --> USA900 in <i>STEREO</i> -->
+
-
** JBL MR835s <i>in parallel</i> on channel 1[2]
+
-
** CSX35s <i>in parallel</i> on channel 2[1]
+
-
* Bi-Amp/Quad Speakers with crossover: MX1400 house out --> 2-way crossover
+
-
** low-pass crossover at max --> USA900 in <i> STEREO</i> --> JBL MR835s on left/right channels
+
-
** high-pass at selectable --> PB2 in <i>BRIDGE MONO</i> --> CSX35s <i> in parallel</i> as directed for bridge mono
+
-
* Bi-Amp/Bad Ideas Subs: MX1400 house out --> 2-way crossover
+
-
**low-pass crossover at selectable --> PB2 in <i>BRIDGE MONO</i> --> Bad Ideas Sub as directed for bridge mono
+
-
**high-pass crossover at selectable --> USA900 in <i>STEREO</i> -->
+
-
***JBL MR835s <i>in parallel</i> on channel 1[2]
+
-
***CSX35s <i>in parallel</i> on channel 2[1]
+
-
When driving both the JBL MR835s and CSX35s off the same amplifier, put the JBLs together and the CSX35s together, and use individual channel gain control to prevent overdriving either pair (mixing JBLs and CSX35s on the same channel will either overdrive the CSX35s, or prevent full utilization of the JBLs)
+
*For use when the PRX612s are committed elsewhere: Check with AVComm. '''DO NOT attempt to use the power amplifiers or non-powered loudspeakers unless you actually know what the fuck you're doing.''' AVComm training means you know how to use the PRX612s, not that you know how to use any and all AVComm equipment. If you want us to trust that you know how to use some particular equipment, talk to us about the setup in question in particular.
-
 
+
-
Note that the USA900 is rated to handle 8 Ohms on bridge mono, while the PB2 is rated to handle 4 Ohms in bridge mono configuration (both can accept impedances of 4 Ohms and above per channel in stereo configuration)
+
-
 
+
-
Both the JBLs and CSX35s are currently set up to connect to the amps through banana plugs. All pre-amplification avcomm equipment is configured to use RCA cables. Specific cables for each speaker set, as well as stereo stackable RCA-RCA patch cables, 1/8" TRS--> stereo RCA, 1/4" TRS--> stereo RCA and 1/4" TS --> mono RCA are available through ec-avcomm for use with the portable sound systems.
+
-
 
+
-
If you don't understand what part of your desired configuration means, ask someone who does before your event.
+
==Equipment Lending Policy==
==Equipment Lending Policy==

Revision as of 03:45, 23 April 2012

AVComm has some of your audio-visual needs. If you have any questions on how to setup something up, let us know at ec-avcomm@mit.edu.

Contents

Current Officers

  • Ben Lehnert - 5E
  • Gabriel Karpman - 5E

Inventory

Portable/Party Equipment

  • 2x JBL MR835 Loudspeaker (3 way, 8 Ohm, 250W RMS/100W peak (pink noise), 38Hz-20kHz)
  • 2x CSX35-S2 Loudspeaker (2 way, 8 Ohm, 150W RMS/375W peak, 60Hz-18kHz)
  • 1x Crown Power Base-2 Amp (400W/Channel; 4 Ohm per channel; currently semi-functional. will hopefully be repaired or replaced before the end of SP2012)

Talbot Lounge

  • HD Television
  • Projector
  • 1 Phillips Surround Sound Receiver w/ DVD Player & iPod Dock
  • VCR
  • HDTV Tuner for Projector

Recommended Speaker Configuration

  • Parties: use the 2 JBL PRX612 powered speakers. Plug them into the wall. Make sure the speakers are OFF. Plug something with 1/4" TS cables into each speaker. Plug the other end of the cable into a line-level audio input. Make sure the speakers are set to Line Level Sensitivity, not mic level turn the speakers on. Typically, the cable used will be 1/8" TRS -> dual 1/4" TS.
  • For use when the PRX612s are committed elsewhere: Check with AVComm. DO NOT attempt to use the power amplifiers or non-powered loudspeakers unless you actually know what the fuck you're doing. AVComm training means you know how to use the PRX612s, not that you know how to use any and all AVComm equipment. If you want us to trust that you know how to use some particular equipment, talk to us about the setup in question in particular.

Equipment Lending Policy

If the EC sound system is used for a hall party or other hall event, it must be returned to the AV closet in Talbot within two days of the event unless there is another event scheduled by a different hall within those two days, in which case it must be returned to the AV closet or transported to the other hall at least two hours prior to the other event. If a hall doesn't comply with the first of these two conditions, they will be fined $25.00 a day for each day that the equipment remains on the hall after the two day grace period. If another hall event is within the two days, the hall hosting that event gains responsibility of the system.

Personal tools